How to Remove the Rear Drum on Vehicles

How to Remove the Rear Drum on Vehicles

How to Remove the Rear Drum on Vehicles

by Contributing Writer

Updated June 12, 2017

Vehicles Motor Co. The Vehicles comes standard with presence disk brakes, and depending on the model year and trim tied, either buttocks drum or magnetic disk brakes. The drum brake design adopted by Vehicles the Vehicles is reasonably different than many other Vehicles. In particular, removal of the drum forum is more complicate than on many other small cars. Armed with a small cognition and a short perseverance, the amateur machinist can remove the drum and perform his own brake drum brake service.

Under The hood :

How to Remove the Rear Drum on a Suzuki Aerio

Loosen the lug nuts on the rear wheels of the car with a lug wrench then raise the rear off the ground with a jackfruit until the tires are off the grind. placement a specify of jack stands under the rear axle to support the cable car, and then lower the jack until the car is resting on the jack stands .

Remove the lugsail nuts, pull the tires off the car and set the tires aside. Locate the rubber spark plug in the rear of the brake drum and pull it out with a pair of acerate leaf nose pliers. Insert a apartment screwdriver into the hole and under the adjuster lock tab inside the drum .

Insert a brake spoon into the access hole where you placed the screwdriver then turn the adjuster up to loosen the brake shoes. Move to the front man of the brake drum and locate the Phillips head screws on the face of the barrel .

Remove the two screws with an affect driver and mallet. Set the screws aside for immediately .

Grasp the barrel on either side with your hands and pull the barrel straight back toward you. carefully slide it off the hub and steering wheel studs. Repeat the march for the face-to-face side of the car .

Items you will need

  • Lug wring
  • Jack
  • Jack stands
  • flat screwdriver
  • Brake spoon
  • Impact driver w/Phillips piece
  • mallet

How to Remove the Rear Drum From a Nissan Altima Use lug wrench, 1/2 inch repel and steering wheel lock to loosen all lug nuts. place the hydraulic jack in the rear center jacking point for your vehicle. Close the valve by turning clockwise and raise the vehicle and the buttocks tires off the footing.

Place jack stands under both sides of the back of the vehicle at the suspension points. Raise the jack higher if necessary to accommodate the jack stands. Remove the lug nuts from the rear wheel and put them in the hubcap so they do n’t get lost. Locate the slot in the back of the brake drum where the alteration gear is located. This is normally covered by a rubber stopper that is removed by hand. Set it aside so it can be replaced late. Engage the adjustment gear with your brake smooch and turn counter-clockwise until the drum is free and can be pulled free of the brake shoes. If removing both drums use the like process for both sides .

Items you will need

  • Lug wrench
  • Hydraulic jack
  • Jack stand
  • 1/2 inch drive ratchet
  • Wheel lock
  • Brake spoon

How to Remove the Rear Drum on a 2002 Ford Focus Park the vehicle on a firm and flat surface. Put automatic transmissions in park and put manual transmissions in first or reverse gear. Do not set the emergency brake. securely block the front wheels to prevent movement of the car. Loosen the lugsail nuts on the rear wheel one wide twist and then jack the cable car up. Place the car securely on an axle base. wholly remove the lugsail nuts and pull the rack off. Remove the four retain bolts that secure the drum and hub forum. The bolts are accessed from the rear of the brake, and can be best reached with a socket wrench, swivel arranger and extension. If you do not have a pivot arranger, then remove the retain bolt that secures the lower end of the strut and swing the tittup out of the way to give clear access to the barrel assembly retaining bolts. If the fomite is equipped with ABS brakes, then disconnect the ABS wire by pulling the plug out of the receptacle on the brake support plate. Pull the drum and hub off the axle spindle. If the drum is difficult to remove, beginning be certain the parking brake is amply disengaged. Firmly tap the outside shoulder of the barrel with a rubber or plastic mallet to loosen the drum. This is the drum-removal operation as recommended in the Focus shop manual. An alternate drum-removal procedure is to remove the hub nut that holds the barrel to the hub and then pull the brake drum straight off the hub. To access the hub nut, first pry off the hub addict ceiling. Be careful not to damage the cap so that it can be reused during reassembly. Use a big socket and circuit breaker bar to remove the hub nut. If the drum is difficult to remove, first be indisputable the parking brake is amply disengaged. Firmly tap the away shoulder of the drum with rubber or fictile mallet to loosen the drum .

Items you will need

  • bicycle blocks
  • Lug testis wrench
  • car jack
  • Safety stand
  • Socket wrench set with ratchet handles, swivel arranger, extensions and big circuit breaker bar
  • mallet
  • Penetrating oil
source : https://tonupboys.com
Category : Car Brakes