When To Replace A Toyota Brake Caliper

When To Replace A Toyota Brake Caliper
Brake calipers final about 75K miles. If your Toyota is nearing that age, you may start wondering how you can recognize failing brake calipers and then replace them before they get excessively bad. This diagnostic guide will walk you through the process of checking your brake calipers and then give you the basics on replacing the calipers.

Signs That You Need New Brake Calipers

here are some signs that your brake calipers have gone bad :

  • Vehicle pulling or steering to one side when the brakes are either applied or not applied
  • Squealing or clunking noise coming from the braking system
  • Brakes not releasing quickly

basically, if you notice that your Toyota ’ s braking performance has become erratic, then you might want to take some time to check your brake calipers.

Checking Your Brake Calipers

Changing caliper image credit : hardtopte72 To diagnose wear brake calipers, you have to remove your wheels and then visually inspect the calipers and brake pads. Look for the follow issues :

  • Uneven pad wear (typically caused by corrosion on guide pin surfaces)
  • Brake fluid leakage at the piston
  • Stuck or malfunctioning piston
  • Cracks on the caliper caused by overheating
  • Bleed screw leakage caused by corrosion

even if you check all of your brake calipers and you find that alone one of them is no longer working, you still should replace your brake calipers in pairs ( on the like axle ).

Why do Brake Calipers Need to be Replaced in Pairs?

If you only replace one brake caliper rather of both calipers on the lapp axle, you ‘ll notice uneven braking performance. It ‘s because the new bracken caliper will cause the pads to grab the rotor better compared to the old one. This will make your car to veer to one side when the brakes are applied, which is dangerous. This besides results in accelerate, uneven tire wear. fortunately, OEM brake calipers can be low-cost on-line compared to dealership prices. You can save a lot of money by ordering genuine OEM Toyota successor calipers from us.

Replacing Your Brake Calipers: the Basics

Old caliper prototype credit rating : hardtopte72 When it ’ mho clock to replace your brake calipers, you ’ ll find that it ’ s a dim-witted and aboveboard process that basically consists of unbolting the caliper from the caliper bracket, disconnecting it from the brake line, and then installing the new caliper. however, there are a few important things to keep in mind :

1. Replace the Flexible Brake Lines Too

The compromising brake lines will get worn out over time. Like many of the other parts on your Toyota, clock time, the hot/cold weather, and continual use lawsuit wear and tear. If you ‘re using rubberize brake lines, the rubber deteriorates over meter, and bantam condom particles can enter the brake fluid and cause obstruction. Rubber brake lines can besides get swell inside the brake channel. This narrows the path for the brake fluid, and limits the force the brakes can apply. This means you wo n’t have enough blackmail to stop the car promptly and safely. so if you have an old devolve brake caliper, chances are beneficial your brake lines are in the same shape. It ca n’t hurt to replace them along with the calipers.

2. Flushing the System is Recommended and Bleeding the Brakes is Required

When you replace your brake calipers, vent will get into the brake lines. That will cause a drop in brake fluid press, which decreases the ability of your brakes. This article offers a more exhaustive explanation of why you should bleed the brakes while replacing your calipers. If you are changing the calipers, it ‘s a great idea to besides flush the brake organization and put in brand new bracken fluent. Brake fluid is hygroscopic, which means that it attracts water. Old brake fluent normally has water in it. The water will create corrosion in your newfangled calipers much more promptly than clean fluid would. Flushing the brake fluid is cheap and easy, specially compared to the cost of replacing calipers.

3. Always Torque the Caliper Bolts to Spec

You want to make sure that the caliper bolts are tightened to the correct torsion specification. Calipers are national to a bunch of vibration, which will cause the bolts to loosen if they are not tightened correctly. If the bolts loosen the caliper can be damaged, and the cable car can be dangerous to drive. If you have any questions about checking your calipers or replacing them, we would love to hear from you. Written by Jason Lancaster

reservoir : https://tonupboys.com
Category : Car Brakes