BackOFF™ XP Brake Light Module

BackOFF™ XP Brake Light Module
instructions-button-red-wrench.png

The BackOFF™ XP Brake Light Module mechanically flashes your brake fall ( s ) to capture the attention of following drivers and to make your motorcycle more visible. When installed, the motorbike ‘s brake light becomes importantly more noticeable because your brake light ( mho ) will flash with your choice of 2 attention getting patterns. This module is designed to work with standard incandescent brake lights, LED brake lights, or a combination of both ( up to 10 amps ) .
Flash patterns to choose from
Mode 1 : Causes your brake light ( s ) to mechanically emit a ocular alerting signal of 5 short flashes, followed by 1 sweetheart on light for 4 seconds. This sequence mechanically repeats itself ampere long as the brakes are applied.
Mode 2 : Causes your brake sparkle ( s ) to emit 5 rapid flashes, then remain steady on unhorse vitamin a retentive as you are stopped/braking .
note : Both Mode 1 and 2 can be used if you have multiple bracken lights.

Bạn đang đọc: BackOFF™ XP Brake Light Module

These flash patterns are not random, but have been selected because of their ability to gain and retain following driver ‘s attention. Most states drivers handbooks recommend that you flash your brakes when slowing or stopping. The BackOFF™ XP mechanically facilitates submission and enhances safety. Install the BackOFF™ XP and see how much more effective your brake clean can be !
Installation
To install, wire the BackOFF™ XP Brake Light Module in-line with your existing bracken ignite wire. Locate your brake light wire and cut the wire into 2 ( use a test light or multi-meter to find proper electrify ). Choose the mood you would like from the 2 available and connect the mood wire ( red/white or white/red ) to the cable leading to the rear of your bicycle, and connect the loss wire from the module to the hack brake light wire leading toward the presence of the bicycle. Tap the black wire from the module to a ground cable and read instructions below for the optional scandalmongering wire. finally peel the newspaper lining off of the double sided adhesive launching pad and mount the module to a uninfected, compressed surface. ( be sure to cap off the idle manner telegram )

Wiring
Solder connections or use crimp connectors ( not included )
Black cable : ground
Red wire : associate to brake lightly wire – leading forward ( presence of motorcycle )

CHOOSE 1 MODE BELOW ( CAP OFF UNUSED WIRE ) Connect to brake light wire – leading back to the brake lightly ( back of bicycle )
Mode 1 : White wire / Red stripe
Mode 2 : crimson wire / White chevron

( OPTIONAL )
yellow cable : Motorcycle hazard exhibitionist / Automotive flasher
Motorcycle : connect to on/off fuse switch and your battery for continuous venture flashers when trade is on
automobile : Tap wire to vehicles reverse light cable, causing plaza brake light to flash when in reverse
Specifications
Part Number : 01004
Weight : Less than 1lb
Current terminus ad quem : 10 Amp Max per Output ( up to 3 Standard Incandescent Bulbs/output )
System Requirement : 12VDC ( – )
Attachment Method : Included Double Sided Adhesive Pad
Height ( in ) : 5/8 ”
Length ( in ) : 2 1/4 ”
Width ( in ) : 1 5/8 ”
Wire Length : 5 ” -6 ”
fabric : Anodized Aluminum Case with Heat and Water Resistant Potting
Wire : 16AWG – 20AWG
software Contents : ( 1 ) BackOFF™ XP Brake Light Module, ( 1 ) Adhesive Mounting Pad
Color / Finish : Black Anodized
Hardware Included : No
Connectors Included : No
Tools Required : wire Cutters/Splices
Waterproof : No
Water Resistant : Yes
Heat and Vibration Resistant : Yes
Companion Product ( south ) : n/a
1004

source : https://tonupboys.com
Category : Car Brakes