How to Bleed the Brakes – Toyota Corolla

How to Bleed the Brakes – Toyota Corolla
Do your brakes feel spongy ? Does the brake bicycle travel all the way to the deck ? How long has it been since you last changed your brake fluid ( hint : it should be done every 2-3 years ! ) ?
In this position we walk through the steps to quickly and easily flush out the previous bracken fluid and replenish it with fresh stuff !
Note: PracticalMechanic.com is reader-supported. If you buy through links on our site, we may earn an affiliate commission – at no cost to you. Thank you for your help keeping this site active.
This is a pretty easy maintenance item to perform on your fomite, it will take you about an hour or two depending on how cursorily you can take tires on and off. If you take your Toyota Corolla to a shop, a brake fluid flush will cost you about $ 100-200.

Tools and Supplies:

  • 8mm box-end wrench
  • rag
  • DOT3 or DOT3&4 Compatible brake fluid
  • rubber tubing (preferably transparent)
  • empty bottle (preferably transparent)
  • a partner who is good a following directions…

Easy Steps for Flushing Brake Fluid

Okay, we ’ ra ready to go ! Follow these steps to bleed the brakes. By the room, I am going to go through the manual method which I use here. I should mention that there is a ‘ hands-free ’ method acting that involves purchasing a device like this, which connects to shop atmosphere and you basically have an tune compressor powered vacuum hemophiliac – no brake pump required ! It is actually a pretty neat method acting that I may need to invest in one day. But for now… !

Step 1: Remove the tire from the brake furthest from the brake master cylinder.

This is the rear passenger ’ sulfur side tire. Use a jack and be sure to use jack-stands for base hit purposes. Jack up the vehicle and remove the bore. This will provide access to the brake hemophiliac screw, which is what we want .
( hera is a shoot of the erstwhile brake fluid, hint : it shouldn ’ deoxythymidine monophosphate be brown… )
01-remove-tire-old-brake-fluid

Step 2: Locate the Bleeder Screw and Attach the Tubing.

Locate the brake hemophiliac screw, looks kind of like a dirt zirk, if you know what those look like. Put your 8mm box-end twist on there. then put the well-defined tube onto the nipple. I entirely had bootleg tube, so that can work in a pinch, however transparent tube is better then that you can see if there are any bubbles in the fluid .
02-brake-bleeder-valve-hose
Put the other end of the tube into a clear plastic collection vessel, like an empty water bottle .
03-how-to-bleed-brakes

Step 3: Apply pressure to the Brake Pedal and Open the Bleeder Screw.

Ask your partner to apply pressure to the brake pedal and hold it .
04-press-brake-pedal
While your partner is applying pressure to the bracken pedal, open the hemophiliac screw by turning it counter-clockwise. I found that a 1/4 flex was enough .
Brake fluid will begin to flow out of the metro. Your partner will notice that their foot begins to go down toward the floor.

05-loosen-brake-bleed-nut

Step 4: Close the Bleeder Screw and Release the Brake Pedal.

When the brake fluent coming out of the metro begins to slow down, close the hemophiliac screw .
06-tighten-brake-bleed-bolt
When the hemophiliac screw is closed, your collaborator can release the brake pedal .
07-release-brake-pedal

Step 5: Repeat Steps 3 and 4 Several Times, Keeping an Eye on the Brake Fluid Level.

Every 2-3 times you pump fluid out of the brake system, check the brake fluid reservoir. Do not let the degree drop below the minimal crisscross, or you may begin to introduce air bubbles into the system !
repeat this action 10-15 times per brake .
08-brake-fluid-reservoir

Step 6: Add Brake Fluid to the Max Fill Line.

When the fluid level is low, add the right brake fluid ( check your fomite ’ s manual ). Generally you will want a brake fluid that is DOT3 compatible .
09-brake-fluid
Don ’ deoxythymidine monophosphate leave the report off the brake fluid reservoir or the brake fluid bottle for excessively long. Brake fluid will suck up moisture if exposed to the air excessively long.

10-brake-fluid-reservoir-full

Step 7: Repeat the Same Procedure for the Rest of the Brakes.

The adjust regulate is to go from the Passenger ’ south side rear tire, to the Driver ’ south english rear run down, to the Passenger ’ s side battlefront run down, to the Driver ’ second side front tire .
I hope you found this guide helpful ! As constantly, if you have any comments, questions, or suggestions, please leave me a note in the comments section below !

Tools and Supplies Used:

  • 8mm box-end wrench
  • rag
  • DOT3 or DOT4 brake fluid
  • rubber tubing (preferably transparent)
  • empty bottle (preferably transparent)
  • a partner who is good a following directions…
generator : https://tonupboys.com
Category : Car Brakes